When you need shower wall panel installation pocatello ID homeowners trust, our crew seals the walls, sets the panels level, and leaves a shower that wipes clean in seconds. We install acrylic and composite surrounds over tile, backer board, or a fresh stud wall, and we waterproof every seam before the first drop of water hits it. Most jobs finish in a single day.
Shower wall panel installation pocatello ID is the process of fitting large-format acrylic, composite, or laminate panels over your shower walls in place of tile or a failing surround. We measure the alcove, cut each panel to the valve and showerhead openings, bed it in adhesive, and seal the seams with silicone caulk rated for wet areas. Panels lock together with tongue-and-groove joints, so there is no grout line to scrub and no thinset mortar to cure.
In Pocatello, most of the housing stock was built before 1990, and the original tile surrounds in those homes are cracked, caulked over three times, and hiding moisture behind the wall. If you have been searching for shower surround near me pocatello, the fix is usually a panel system rather than another round of grout repair. We pull the old surround, check the backer board, and install new panels the same week.
Every panel install starts with a measure visit and a written price. The list below covers what we handle on a standard alcove job. If your shower needs a new pan, valve, or drain, we quote that separately so you can see the difference.
We remove the old tile, surround, or panel system, pull the valve trim and drain strainer, and haul the debris away. Tear-out on a standard 60-inch alcove takes two to three hours, and we protect the floor and tub apron before we start.
We repair or replace cement backer board, tape and seal the joints, and roll on a waterproofing membrane. This is the layer that keeps water out of your framing. We do not panel over wet or soft board.
We dry-fit each panel, cut the shower valve, showerhead, and niche openings, and check the panel edges against the shower base. Panels are bedded in construction adhesive and locked at the tongue-and-groove joints.
Every seam, corner, and fixture penetration gets a bead of 100 percent silicone caulk rated for wet areas. We smooth the bead by hand and let it skin overnight. This is the step that keeps a panel surround watertight.
We reinstall the shower valve trim, set the drain strainer, and run hot water for ten minutes to check for leaks. You get a walkthrough, a wipe-down, and a reminder to wait overnight before the first shower.
We measure the alcove width, depth, and height, note the shower valve and drain positions, and check whether the existing wall is flat enough to panel over. You get a written price the same visit. Most quotes take 30 to 45 minutes.
We remove the old surround or tile, pull the shower valve trim and drain strainer, and inspect the backer board and framing. If we find soft wood or a cracked shower pan, we tell you before we go further. Tear-out on a standard 60-inch alcove runs two to three hours.
We install or repair cement backer board, tape and seal the joints, and roll on a waterproofing membrane. A shower pan liner and drain wrench come out here if the pan needs attention. Prep and waterproofing take about half a day and must dry before panels go up.
We dry-fit each panel, cut the valve and showerhead openings with a jigsaw or oscillating tool, then bed the panels in construction adhesive and lock the tongue-and-groove joints. A level and measuring tape stay in hand the whole time. Panel setting takes three to four hours.
We run a bead of silicone caulk at every seam, corner, and fixture penetration, reinstall the shower valve trim and drain strainer, and run hot water for ten minutes to check for leaks. You get a walkthrough and a wipe-down before we pack up.
We measure the alcove width, depth, and height, note the shower valve and drain positions, and check whether the existing wall is flat enough to panel over. You get a written price the same visit. Most quotes take 30 to 45 minutes.
Cuts panel openings for the shower valve, showerhead, and niche without cracking the acrylic. It also trims backer board and old caulk cleanly.
Spreads adhesive in even ridges so the panel beds flat against the wall with no hollow spots behind it.
Runs a consistent bead at every seam, corner, and fixture penetration. We use silicone rated for wet areas, not painter's caulk.
Keeps the first panel plumb so the tongue-and-groove joints line up and the top edge stays level across the alcove.
Removes and resets the drain strainer and valve connections when the pan or plumbing needs attention before the panels go up.
Used on the tile portion of a mixed job or when we cut backer board and trim pieces to fit around the shower base.
A 60-inch alcove in Highland with cracked ceramic tile, three layers of old caulk, and soft backer board near the pan. The homeowner had been quoted a full tile replacement and did not want the mess or the multi-day cure time.
After: We tore out the tile, replaced the soft backer board, waterproofed the wall, and installed acrylic panels in one day. The shower was back in service the next morning, and the homeowner saved roughly 40 percent against the tile quote.
Book this service →A student rental near Idaho State had a yellowed plastic surround with black mold in the corners and a slow drain. Every turnover meant scrubbing and re-caulking, and the mold kept coming back.
After: We removed the old surround, treated the wall, replaced the backer board, and installed new acrylic panels with silicone caulk. We also cleared the drain and replaced the strainer. Turnover cleaning dropped to about fifteen minutes.
Book this service →
A homeowner in the Chubbuck Border Area wanted the tub gone for a walk-in shower. The alcove was 60 inches wide with a cast iron tub, and the valve was original to the house.
After: We pulled the tub, set a new shower base, replaced the valve with a Moen trim kit, waterproofed the walls, and installed panels sized for the new footprint. The job took two days, and the shower gained about 8 inches of usable floor space.
Book this service →Most panel installs start with a problem the homeowner has been living with for months. Here are the ones we see most in Pocatello.
Ask a pro →We tear out the failed tile, replace any soft backer board, waterproof the wall, and install panels with two or three seams instead of hundreds of grout lines. The wall dries out and stays dry.
We strip the old caulk, treat the wall, and seal the new panels with silicone caulk. Panels wipe clean, and there is no grout to hold moisture. We also check the exhaust fan while we are there.
We remove the old surround, inspect the pan and drain, and install new acrylic or composite panels. Most swaps are done in a day, and the shower looks new without a full remodel.
We open the wall, find the source, and repair the waterproofing or the drain connection before installing panels. If the shower pan is cracked, we replace it and set the panels after the new pan is level.
$1,200 - $3,400 depending on scope
Typical 2026 pricing for a standard alcove panel install in Pocatello runs $1,200 to $3,400, depending on tear-out, wall condition, and the panel system you choose. A simple panel-over-tile job sits at the low end. Full tear-out with new backer board, a new shower valve, or a tub-to-shower conversion pushes toward the top. We give you a written price after the measure visit, and it does not change unless you approve added work.
Panels cost less than tile because there is no grout, no tile saw work, and no multi-day cure. You get a watertight shower in a day, and you never scrub a grout line again.
A standard 60-inch alcove uses fewer panels and less cutting than a 48-inch or a custom layout. Odd angles and niches add cutting time and trim pieces.
Get a quote ↗Sound backer board means a fast install. Soft or missing board means we replace it and waterproof the wall, which adds material and about half a day of labor.
Get a quote ↗Acrylic panels cost the least. Composite and laminate panels cost more but look closer to stone. We bring samples so you can compare before you decide.
Get a quote ↗A new shower valve, drain, or pan adds labor and parts. If the valve moves, we cut a new opening in the panel and set the trim to match.
Get a quote ↗Most standard alcove panel installs in Pocatello run $1,200 to $3,400 in 2026, including tear-out, backer board prep, panels, and caulk. A simple panel-over-existing-wall job sits at the low end. Full tear-out with new backer board, a shower valve swap, or a tub-to-shower conversion pushes toward the top. We give you the number in writing before we start.
For most Pocatello homes, acrylic panels from Sterling, DreamLine, or Vigo hold up best against hard water and cold winters. Composite and laminate panels cost more but look closer to stone. We bring samples so you can compare finishes in your own bathroom light, and we match the panel to your shower base and valve trim.
Yes, if the tile is solid and the wall is flat. We scuff the tile, fill any missing pieces, and bed the panels in adhesive over the existing surface. If the tile is loose, cracked, or the wall is soft behind it, we tear it out and start with cement backer board. We check before we quote.
We do, and we cover all of Pocatello and Bannock County, including 83201, 83204, and 83209. Call or text and we will set a measure visit, usually within a few days. We handle the tear-out, waterproofing, panel install, caulking, and cleanup, and we test for leaks before we leave.
Call or text and we will measure your alcove, show you panel samples, and give you a written price the same visit. We are licensed, insured, and we warranty our panel installs. Most jobs are scheduled within the week.
Get Free Estimate +19863369120 →Call us at +1 986-336-9120 or email info@showerproinstallation.com and we'll set up a free on-site measure. We answer the phone Monday through Friday, 8:00 to 18:00, and we return every message the same business day. For a leaking shower or a valve that's spraying, call any time - we run emergency call-outs 24/7.