When you need walk in shower installation in Alameda, ShowerPro Installation handles the whole job: tear-out, waterproofing, tile, glass, and final test. We work the older homes around Alameda Park and the newer builds near Alameda Terrace, and we know how Bannock County's cold winters treat a bad shower pan. One crew, upfront pricing, and a shower that drains right the first time.
Licensed · Upfront options · Clean work areas · Written guarantees
Alameda shower work splits into two piles: full replacements in older homes and accessibility upgrades in newer ones. If you have been hunting for walk in shower installation near me Alameda ID, this is the full list of what we install, repair, and replace in the neighborhood. Every job starts with a measurement and a drain check, and every job ends with a wet test.
We measure your Alameda bathroom, map the drain and valve locations, and lay out a shower that fits the room instead of forcing a kit into it. Tile size, niche placement, bench height, and glass swing all get decided before demo day.
View details ↗02Full gut remodels for Alameda homes with failing tile, mold behind the wall, or a layout that wastes space. We handle demo, framing repairs, new backer board, waterproofing, tile, and glass, and we keep the rest of the house clean while we work.
View details ↗03The most common job we run in Alameda: pulling a cast iron or fiberglass tub and building a walk-in shower in the same footprint. We cap the old drain line, reset the pan, and usually gain six to eight inches of usable floor space.
View details ↗04For Alameda homeowners planning ahead or caring for a parent, we build a shower with no curb to step over. The floor slopes to a linear or center drain, and the whole entry stays flush with the bathroom floor.
View details ↗05We install ADA compliant showers in Alameda with the right clear floor space, grab bar blocking, and a seat at the correct height. Blocking goes in before the backer board so bars can be added or moved later without opening the wall.
View details ↗06Curbless showers need a recessed floor or a sloped mortar bed, and Alameda's older subfloors often need sistering before that happens. We frame it, slope it, waterproof it, and set a linear drain so the water has one clear path out.
View details ↗07A two-inch curb is the middle ground for Alameda homes that cannot take a full floor recess. It keeps the pan simple, still stops splash, and cuts the step-over height by more than half compared to a standard tub apron.
View details ↗08We set acrylic, cultured stone, and tile-ready pans with a proper mortar bed underneath so the base does not flex or crack. In Alameda homes with uneven floors, we level first and check the slope with a level before the pan goes down.
View details ↗09Cracked or spongy bases are common in Alameda houses built before the 1980s. We cut out the old base, inspect the subfloor and drain for rot, then set a new base and re-caulk the full perimeter.
View details ↗10We swap old two-handle valves for modern pressure-balance or thermostatic valves from Moen, Delta, Kohler, and Grohe. In Alameda homes with original plumbing, we open the wall, replace the valve body, and pressure-test before closing it back up.
View details ↗11Slow drains and weeping joints get fixed at the source. We pull the old drain with a drain wrench, inspect the trap, and set a new drain assembly sealed to the pan liner so Alameda's hard water and soap scum have nothing to catch on.
View details ↗12When a shower backs up or the pressure drops, the problem is usually behind the wall. We camera the line, replace corroded galvanized sections, and correct the venting so the drain pulls fast again.
View details ↗13This is the step that decides whether an Alameda shower lasts ten years or two. We use Schluter Systems and Laticrete membranes over cement backer board, seal every seam and corner, and flood-test the pan before tile goes on.
View details ↗14We set ceramic, porcelain, natural stone, and glass mosaic tile with a notched trowel and thinset mortar, then grout and seal it. Alameda customers usually pick large-format porcelain for easy cleaning or a mosaic accent band for the niche.
View details ↗15Acrylic and solid surface panels go up fast and wipe clean, which suits Alameda rentals and busy family bathrooms. We set them plumb over new backer board so the seams stay tight and the caulk lines stay straight.
View details ↗16We measure for glass after the tile is set, not before, so the panels fit the finished opening. DreamLine, Vigo, and Sterling enclosures get installed with proper clearances so the door swings free and the seals actually touch.
View details ↗17Frameless glass opens up a small Alameda bathroom more than any other upgrade. We use 3/8-inch tempered glass, heavy-duty hinges anchored into blocking, and a sweep seal that keeps water off the floor.
View details ↗18A door that will not close, drags on the curb, or leaks at the hinge usually needs new rollers, hinges, or a re-hung track. We repair what we can and replace the door when the frame is bent or the glass is chipped.
View details ↗19We build tiled benches and install fold-down seats with blocking anchored into the framing, not just the tile. For Alameda customers with mobility concerns, the seat height gets set to match the grab bars.
View details ↗20Grab bars only work if they are anchored into solid blocking. We add blocking during the remodel, then mount bars at the right height and angle, and we can retrofit bars into an existing Alameda shower with proper toggle anchors.
View details ↗21A recessed niche keeps shampoo off the floor and out of the way. We frame it between studs, waterproof it with the rest of the wall, and tile the inside so it drains and cleans like the rest of the shower.
View details ↗22Handheld heads from Moen, Delta, and Hansgrohe get installed with a slide bar and a drop ell so the hose does not kink. We check flow rate against EPA WaterSense ratings so you keep good pressure without wasting water.
View details ↗23A shower with no fan grows mold fast in an Alameda winter, when windows stay shut for months. We install vent fans ducted to the exterior, add wet-rated recessed lights, and wire them to a single switch so the fan actually gets used.
View details ↗24Three-piece surrounds and full enclosures go in over new backer board with sealed seams and a bead of silicone caulk at every joint. We check the panels for plumb before fastening so the doors line up later.
View details ↗25We re-caulk, re-grout, replace failed seals, and re-set loose tile on Alameda showers that are otherwise sound. A maintenance visit every couple of years keeps a good shower from turning into a tear-out.
View details ↗26Water stains on the ceiling below or a soft spot at the curb mean the pan or the drain seal has failed. We trace the leak with a flood test, open only what needs opening, and repair the waterproofing before we re-tile.
View details ↗27Failed caulking and grout are the number one cause of hidden rot in Alameda showers. We cut out the old material, dry the joint, and re-caulk with silicone, then seal the grout so it stops absorbing water.
View details ↗28When the pan is cracked, the tile is tenting, and the valve is original, replacement beats repair. We tear out to the studs, rebuild the whole assembly, and haul the debris away the same day.
View details ↗29A burst valve or a pan that is dumping water into the floor below cannot wait. We take emergency calls around Alameda, shut the water down, stabilize the leak, and schedule the permanent repair right after.
View details ↗Every Alameda job starts with a measurement and a drain check, because the drain location decides what kind of pan and slope you can use. In older homes around 83204, that often means opening the floor to replace a cast
Old cast iron traps corrode from the inside and restrict flow, so a new shower can drain slow even after the pan is replaced. We find this on most pre-1970 homes in the 83204 area.
We camera the drain line during the estimate. If the trap is scaled or cracked, we cut it out and replace it with PVC before the new pan goes down, so the shower drains like new from day one.
Book a visit →
A pan set on an uneven floor flexes, and flexing cracks the base and opens the caulk line. This is common in homes near Alameda Park that have settled over decades.
We check the floor with a level and a measuring tape, sister or shim the joists where needed, and set every pan on a full mortar bed so the base has zero movement.
Book a visit →
Alameda winters push exterior wall temperatures down, and a shower on an outside wall can feel cold and sweat condensation behind the tile. That moisture feeds mold.
We insulate exterior walls before backer board goes up, add a properly ducted vent fan, and seal every penetration so warm moist air leaves the house instead of sitting in the wall cavity.
Book a visit →
01Water stain on the ceiling below the bathroom
02Soft or spongy spot at the shower curb
03Cracked shower pan or base
04Shower door will not close or drags on the curb
05Low water pressure or temperature swings
Typical 2026 pricing for walk in shower installation in Alameda runs from about $2,800 for a simple acrylic surround over an existing pan up to $9,500 or more for a full custom tile job with frameless glass and a curbless floor. A standard tub-to-shower conversion with porcelain tile and a framed glass door usually lands between $4,500 and $7,000. Older Alameda homes can push the number up if the drain line needs replacing or the subfloor has rot. We give you a written estimate before demo starts, and the price does not move unless we open a wall and find something we could not see.
We run regular crews in Alameda six days a week and take emergency calls 24/7 for burst valves, active leaks, and pans dumping water into the floor below. Standard estimates are free and usually scheduled within two business days. If you need same day shower installation Alameda, call early and we will tell you honestly whether we can fit it in that day.
A pre-made acrylic pan is the cheapest option. A curbless or barrier-free pan requires floor recessing, a sloped mortar bed, and often a linear drain, which adds labor and materials. If the existing drain line is cast iron and corroded, replacing it adds to the total.
Schedule now ↗Acrylic and solid surface panels install faster and cost less. Ceramic and porcelain tile take longer, need thinset mortar and grout, and cost more in labor. Natural stone and glass mosaic sit at the top of the range and require more careful setting.
Schedule now ↗A framed enclosure is the budget choice. Frameless 3/8-inch glass with heavy hinges adds a meaningful amount. Valve upgrades to thermostatic models from Grohe or Hansgrohe, plus handheld heads and slide bars, also move the number.
Schedule now ↗Alameda is compact, and most of our routes run off the main streets that feed the neighborhood. We use a few well-known spots as orientation points when we dispatch crews, and we plan around airport traffic and school hours so we are not sitting in a driveway waiting for a street to clear.
A central reference point for the surrounding residential blocks. Crews use it to orient themselves when routing to addresses on the streets that ring the park.
A useful navigation anchor for the family streets nearby. We time arrivals outside drop-off and pick-up windows so trucks are not blocking the school zone.
The airport sits close to the Alameda area and its traffic patterns affect how we schedule morning and evening arrivals on the nearby corridors.
These are our most frequently served ZIP codes. Nearby areas may also qualify—call if you do not see yours.
Alameda Park · Alameda Terrace · South Alameda · Near Alameda Middle School
Our team can help if your question is not answered here.
Call +19863369120 →Most Alameda jobs run $2,800 to $9,500 in 2026, with a typical tub-to-shower conversion landing between $4,500 and $7,000. Acrylic surrounds sit at the low end, and custom tile with frameless glass and a curbless floor sit at the top. Older homes in 83204 can add cost if the drain line or subfloor needs work.
The right company is the one that pulls the permit, uses a real waterproofing membrane, flood-tests the pan, and gives you a written price before demo. We do all four on every Alameda job. Ask any contractor you are considering those same questions and compare the answers.
Yes, if the work involves moving or replacing the drain, changing the valve, or altering the framing. Bannock County jurisdictions require a plumbing permit for those changes, and the work gets inspected. Cosmetic changes like re-caulking or swapping a showerhead do not need one.
A tub-to-shower conversion with tile usually takes four to six working days from demo to final wet test. An acrylic surround over an existing pan can finish in two days. Custom curbless jobs with a recessed floor and frameless glass run closer to seven to ten days.
We take 24/7 emergency calls for active leaks, burst valves, and pans dumping water into the floor below. We will shut the water down and stabilize the leak the same day, then schedule the permanent repair. Call +19863369120 and describe what you are seeing.
Call ShowerPro Installation at +1 986-336-9120 for a free on-site measure and a written price. Licensed, insured, and serving all of pocatello and Bannock County.
Tell us what you are seeing and where you are located. Our team will call to confirm the right appointment type and timing.