When you need walk in shower installation in Fairway Estates, ShowerPro Installation handles the whole job: tear-out, plumbing, waterproofing, tile, and glass. We work the 83201 and 83204 neighborhoods around the golf course, plus Highland and Mountain View, and we build showers that hold up to Bannock County winters. Licensed, insured, and we leave a dry floor behind.
Licensed · Upfront options · Clean work areas · Written guarantees
Fairway Estates homeowners call us for everything from a single shower door replacement to a full gut-and-rebuild. The most common request is a tub-to-shower conversion in a 1980s hall bath, followed by curbless installs for aging-in-place. If you have been searching for walk in shower installation near me Fairway Estates ID, we cover the full list below with one crew and one warranty.
We measure your Fairway Estates bathroom, lay out the pan, niche, bench, and glass, and pick tile that fits the home's era. Most designs land in 3 to 5 business days. We account for the sloped ceilings and odd alcoves common in 83201 builds.
View details ↗02Full tear-out and rebuild for Fairway Estates homes still running original 1980s tile and brass fixtures. We replace the valve, pan, backer board, and waterproofing in one scope. Typical timeline is 5 to 8 working days. We haul away all debris.
View details ↗03The number one call we get in Fairway Estates. We pull the tub, cap or reroute the drain, frame the new pan, and finish with tile or acrylic panels. Most conversions run 4 to 6 days. We handle the permit and inspection.
View details ↗04Zero-threshold entries for Fairway Estates homeowners planning to age in place. We reinforce the subfloor, set a linear drain, and slope the pan at 1/4 inch per foot. Grab bars and a fold-down seat are common add-ons. ADA-compliant clearances available.
View details ↗05We build to ICC A117.1 dimensions: 60-inch turning radius, 36-inch entry, blocking for grab bars at 33 to 36 inches. Fairway Estates homes with a parent moving in are our typical ADA job. Inspection-ready on the first pass.
View details ↗06Curbless pans require cutting joists or dropping the subfloor. In Fairway Estates we usually recess the pan 1.5 to 2 inches and sister the joists. Schluter Kerdi membrane over cement backer board. Finished floor transitions flush to the bathroom tile.
View details ↗07A 2 to 4 inch curb for Fairway Estates homeowners who want easier entry without a full subfloor drop. Faster install than curbless, still ADA-friendly with grab bars. We stock 60x32 and 60x34 pans on the truck.
View details ↗08Acrylic, cultured marble, or tile-ready pans set level and shimmed. We check the subfloor for rot first, which is common in Fairway Estates homes with older copper drains. Pan liner and pre-slope done to code.
View details ↗09Cracked or flexing bases are a weekly call in 83204. We cut out the old base, inspect the drain and trap, and set a new pan with fresh waterproofing. One-day job in most Fairway Estates bathrooms.
View details ↗10We install Kohler, Moen, Delta, Grohe, and Hansgrohe valves with the correct rough-in depth. Pressure-balance and thermostatic options available. Fairway Estates homes with low winter water pressure get a flow test before we close the wall.
View details ↗11Linear, center, and offset drains set into the pan with proper slope. We use a drain wrench and check the trap arm for clogs before setting. Fairway Estates cast iron drains from the 1970s often need partial replacement.
View details ↗12Supply line and drain work for Fairway Estates remodels. We replace galvanized and aging copper while the wall is open, and we pressure-test before closing. Licensed plumber on every job.
View details ↗13Schluter Systems Kerdi membrane, Laticrete Hydro Ban, and Custom Building Products RedGard are our standard systems. We flood-test the pan for 24 hours before tile. This is the step that stops mold in Fairway Estates bathrooms.
View details ↗14Porcelain, ceramic, natural stone, and glass mosaic. We cut with a wet saw and set with a notched trowel for full coverage. Fairway Estates homeowners lean toward large-format porcelain and a marble-look accent niche.
View details ↗15Acrylic and solid-surface panels for Fairway Estates homeowners who want a fast, low-maintenance finish. Two-day install, no grout lines to scrub. We seal every seam with silicone caulk rated for wet areas.
View details ↗16Framed and semi-frameless enclosures cut to your opening. We template in Fairway Estates, fabricate locally, and install in 7 to 10 days. DreamLine and Vigo stock units available for faster turnaround.
View details ↗173/8-inch tempered glass with minimal hardware. We measure for out-of-plumb walls, which is common in Fairway Estates 1980s builds. Typical lead time is 10 to 14 days from template to install.
View details ↗18Doors that drag, leak, or will not latch get fixed same-week in Fairway Estates. We replace rollers, hinges, sweeps, and seals. If the glass is cracked, we template and order a replacement panel.
View details ↗19Teak, tile, and fold-down seats blocked into the framing for real weight. Fairway Estates aging-in-place clients usually pair a bench with grab bars. We anchor into studs, never drywall alone.
View details ↗20ADA-height grab bars at 33 to 36 inches, anchored into blocking rated for 250 pounds. We add blocking during any Fairway Estates remodel so bars can go in later without opening the wall.
View details ↗21Recessed niches framed between studs and waterproofed with membrane. Fairway Estates clients often ask for a 12x24 niche with a stone shelf. We slope the shelf so water runs off.
View details ↗22Slide-bar handhelds with a 59-inch hose, mounted at the right height for the household. EPA WaterSense models available. We check flow at the Fairway Estates home's actual pressure before recommending a head.
View details ↗23Wet-rated recessed cans and a properly sized exhaust fan vented to the exterior, not the attic. Fairway Estates homes with original 1980s fans are usually undersized. We size the CFM to the bathroom volume.
View details ↗24Acrylic surrounds, tile surrounds, and full enclosure kits set level and sealed. We remove the old surround, repair any rot behind it, and install new backer before the finish goes up. Common in Fairway Estates rental turnovers.
View details ↗25Recaulking, grout repair, drain cleaning, and hardware tightening for Fairway Estates homeowners who want to stretch the life of a good shower. We inspect the pan and valve while we are there. Most visits run 90 minutes.
View details ↗26Water stains on the ceiling below are the usual tip-off in Fairway Estates two-story homes. We isolate the leak with a flood test, then repair the pan, drain, or valve as needed. Same-day diagnosis available.
View details ↗27Failed caulking and cracked grout let water behind the tile. We cut out the old material, dry the joint, and re-caulk with silicone rated for wet areas. Fairway Estates freeze-thaw cycles make this a yearly fix in some homes.
View details ↗28Full replacement when repair no longer makes sense. We tear out to the studs, rebuild the pan and walls, and install new fixtures and glass. Typical Fairway Estates replacement runs 6 to 9 working days.
View details ↗29Burst supply line, failed pan, or a shower that cannot wait. We run 24/7 in Fairway Estates and can set a temporary pan and valve the same day, then schedule the finish work. Call the emergency line any hour.
View details ↗Every Fairway Estates job starts with a 30-minute walkthrough. We check the subfloor, the drain location, the valve rough-in depth, and whether the wall behind the tile is drywall or cement backer board. From there we wr
Freeze-thaw cycles in Fairway Estates crack older copper and push joints apart. Showers that sat unused through a cold snap often leak on first use in spring.
We inspect every supply line and trap arm while the wall is open, replace questionable copper with PEX, and insulate exterior-wall runs before closing up. If a line is at risk, we tell you before the tile goes on.
Book a visit →
Most Fairway Estates homes still have the original acrylic pan and a two-handle valve. Pans flex, weep, and crack; valves lose pressure balance and scald when someone flushes a toilet.
We replace the pan and valve as a package, not one at a time. New pressure-balance or thermostatic valve, new pan with fresh liner, new drain. One permit, one inspection, one warranty.
Book a visit →
Curbless pans need a 1.5 to 2 inch drop. Fairway Estates homes on the east bench often have shallow joist bays or a finished ceiling below, which limits how far we can recess.
We measure joist depth and direction before quoting. If a full curbless drop is not possible, we build a low-threshold pan at 2 to 4 inches, which still gets you easy entry without cutting the ceiling below.
Book a visit →
01Water stain on the ceiling below
02Cracked or flexing shower pan
03Grout and caulk failing every year
04Low water pressure or scalding swings
05Mold that keeps coming back
Typical 2026 pricing for walk in shower installation in Fairway Estates runs $4,200 to $9,800 for a full tub-to-shower conversion, and $7,500 to $14,000 for a custom tile shower with frameless glass. A pan replacement alone is usually $1,800 to $3,200. The biggest cost drivers are whether we drop the subfloor for a curbless pan, the tile you choose, and whether the valve and drain need replacing while the wall is open. We quote a fixed price after the walkthrough, so there are no surprise change orders. If you have been looking for affordable walk in shower installation in Fairway Estates, ask us about acrylic panels and a stock pan, which can bring the total down without cutting the waterproofing.
We run 24/7 emergency service in Fairway Estates for burst lines, failed pans, and leaks you cannot shut off. Standard installs are scheduled Monday through Saturday, 7 a.m. to 6 p.m. Same-day estimates are usually available if you call before noon. We keep a stocked truck on the east bench, so most Fairway Estates jobs start within a week of the estimate.
A curbless pan requires cutting joists or dropping the subfloor, plus a linear drain. That adds $1,500 to $3,000 in labor and materials over a standard low-threshold pan. In Fairway Estates, shallow joist bays sometimes limit how far we can recess.
Schedule now ↗Porcelain and natural stone tile cost more in material and labor than acrylic panels. A tile shower in Fairway Estates typically runs $2,000 to $4,000 more than a comparable panel install. Tile lasts longer and looks custom.
Schedule now ↗If the valve is original 1980s brass, we replace it while the wall is open. That adds $400 to $900 for the valve and labor. Same for a cast iron drain that needs partial replacement, which runs $300 to $700.
Schedule now ↗Fairway Estates wraps around the Pocatello Golf Course on the east bench. We use the course, Highland High School, and Mountain View Park as our main orientation points when routing crews. Most streets off the course are quiet residential, so we park on the street, keep the truck tight to the curb, and carry materials in through the garage or front door.
The course anchors the Fairway Estates neighborhood. We use it as our main reference point when routing to streets on the north and west sides of the community.
Highland High sits just south of Fairway Estates. It is a useful landmark for scheduling around school traffic on weekday mornings when we are heading to jobs in Highland.
Mountain View Park is a familiar reference for the family oriented streets on the south edge of the neighborhood. It helps us confirm which side of the bench a job is on.
These are our most frequently served ZIP codes. Nearby areas may also qualify—call if you do not see yours.
Fairway Estates · Highland · Mountain View · Pine Ridge
Our team can help if your question is not answered here.
Call +19863369120 →Most Fairway Estates jobs run $4,200 to $9,800 for a tub-to-shower conversion, and $7,500 to $14,000 for a custom tile shower with frameless glass. A pan replacement alone is $1,800 to $3,200. Curbless pans and natural stone tile push the number up. We quote a fixed price after the walkthrough.
The best company is the one that pulls the permit, names its waterproofing system, and warranties the labor. We use Schluter Kerdi and Laticrete Hydro Ban, we are licensed and insured in Idaho, and we warranty our workmanship for 5 years. Ask any contractor those three questions before you hire.
Yes, if you are moving the drain, replacing the valve, or changing the pan. Bannock County and the City of Pocatello require a plumbing permit for that work, and it gets inspected. We pull the permit and meet the inspector. A simple door or fixture swap usually does not need one.
A tub-to-shower conversion runs 4 to 6 working days. A full custom tile shower with frameless glass runs 6 to 9 days, plus 10 to 14 days of lead time for the glass. A pan replacement alone is usually one day. We give you a written schedule before we start.
For emergencies, yes. If a pan has failed or a supply line burst, we can set a temporary pan and valve the same day and schedule the finish work after. For a standard install, we can usually start within a week of the estimate. Call before noon for a same-day estimate.
Call ShowerPro Installation at +1 986-336-9120 for a free on-site measure and a written price. Licensed, insured, and serving all of pocatello and Bannock County.
Tell us what you are seeing and where you are located. Our team will call to confirm the right appointment type and timing.