Walk in Shower Installation in Brookside Built for Idaho Winters

Custom Walk-In Shower Design

We design custom walk-in showers for Brookside homes with odd layouts or limited space. Whether you are near Brookside Park or in South Pocatello, we measure your alcove, plan the drain location, and help you pick tile, glass, and fixtures that fit your budget and your bathroom's footprint.

Shower Remodeling

Full shower remodels in Brookside often mean tearing out old tile, replacing the valve, and updating the waterproofing. We handle the entire project: demo, plumbing, backer board, tile or panels, and glass. Most remodels in the 83201 and 83204 ZIP codes take three to five days from start to final walkthrough.

Tub-to-Shower Conversion

Many Brookside homes still have original tubs that are hard to step into and expensive to fill. We convert those tubs to walk-in showers with low thresholds, new pans, and updated fixtures. This is one of our most requested services near the Portneuf River and in the older neighborhoods off South Pocatello.

Barrier-Free Shower Installation

Barrier-free showers remove the curb entirely so you can walk or roll straight in. We install these for Brookside residents who want to age in place or need wheelchair access. The job requires precise floor sloping and a linear drain, and we handle the waterproofing details that keep the floor dry.

ADA Compliant Shower Installation

ADA-compliant showers meet specific dimensions for grab bars, seat height, and entry width. We install these in Brookside for homeowners and caregivers who need code-correct accessibility. We follow ICC codes and verify clearances so the finished shower passes inspection and works for daily use.

Curbless Shower Installation

Low-Threshold Shower Installation

Low-threshold showers have a small curb, usually two to four inches, that is easier to step over than a standard tub. We install these in Brookside homes where a full curbless build is not feasible but the homeowner still wants safer entry. The pan and drain are set to code and tested before tile goes down.

Walk-In Shower Pan Installation

A shower pan is the foundation of any walk-in. We install pre-formed pans and custom mortar beds in Brookside, making sure the slope is correct and the liner is watertight. A bad pan is the number one cause of shower leaks, so we take extra time on the subfloor and drain connection.

Walk-In Shower Base Replacement

When a Brookside shower base cracks or flexes, water gets underneath and rots the subfloor. We remove the old base, inspect for damage, and install a new pan with fresh waterproofing. Most base replacements in the 83201 area take one to two days and include a new drain assembly.

Shower Valve and Fixture Installation

Old valves cause temperature swings and low pressure. We replace shower valves in Brookside with pressure-balanced or thermostatic models from Moen, Delta, and Kohler. We open the wall, solder or crimp the new lines, test for leaks, and patch the opening so it is ready for tile or panel.

Shower Drain Installation

A slow or clogged shower drain in Brookside is often a sign of a failing drain assembly or a blocked trap. We install new drains, replace broken strainers, and make sure the connection to the waste line is solid. We use a drain wrench to seat the new drain and test the flow before closing up the floor.

Shower Plumbing and Drainage

Shower plumbing in older Brookside homes can include galvanized pipes, undersized vents, and questionable DIY repairs. We re-pipe shower lines, correct venting issues, and bring the drainage up to current code. This work often happens during a remodel when the walls are already open.

Shower Waterproofing and Sealing

Waterproofing is the step that prevents mold and rot behind the tile. We apply waterproofing membrane over cement backer board in Brookside showers, seal the seams and corners, and flood-test the pan before tile. Skipping this step is why so many older showers fail.

Shower Tile Installation

We install ceramic tile, porcelain tile, and natural stone tile in Brookside showers. Whether you want a simple subway pattern or a glass mosaic accent, we set the tile with a notched trowel, keep the lines level, and grout with a float for a uniform finish. Tile work is done after waterproofing passes inspection.

Shower Wall Panel Installation

Acrylic shower panels are a fast, low-maintenance option for Brookside homeowners who do not want grout lines. We install panels over cement backer board, seal the edges with silicone caulk, and make sure the panels sit plumb. This is a good choice for rental properties and quick turnarounds.

Shower Glass Door and Enclosure Installation

We install shower glass doors and enclosures in Brookside, including semi-frameless and fully framed styles. We measure the opening after tile is set, order the glass to fit, and install it with proper seals so water stays inside. Most enclosures are installed within a week of the tile curing.

Frameless Shower Door Installation

Frameless glass doors give a Brookside shower a clean, open look with no metal frame to scrub. We use heavy-duty hinges and tempered glass cut to your exact opening. The installation requires precise leveling and anchoring into studs or blocking, which we verify before drilling.

Shower Door Repair and Replacement

A shower door that will not close or leaks at the hinge is a common call in Brookside. We repair rollers, replace seals, and rehang doors that have sagged. If the door is beyond repair, we supply and install a new one that fits the existing opening.

Shower Seat and Bench Installation

Built-in shower seats and benches add comfort and safety for Brookside residents who need to sit while showering. We frame the seat, cover it with backer board and waterproofing, then finish it with tile or stone. Seats are anchored to the wall framing so they support real weight.

Shower Grab Bar Installation

Grab bars need to be anchored into solid blocking, not just tile. We install grab bars in Brookside showers with proper backing, correct heights, and ADA-compliant placement. This is a small job that makes a big difference for safety, especially in homes near Ross Park where many residents are aging in place.

Shower Niche and Shelf Installation

A recessed niche keeps shampoo and soap off the floor and out of the way. We frame and waterproof niches in Brookside showers, then tile the interior to match the walls. We also install corner shelves and floating shelves when a recessed niche is not possible.

Handheld Showerhead Installation

Handheld showerheads are useful for rinsing, cleaning, and accessibility. We install them in Brookside homes with new slide bars, hoses, and vacuum breakers to prevent backflow. This is a quick upgrade that improves daily use and helps with ADA compliance.

Shower Lighting and Ventilation

Good lighting and ventilation prevent mold and make the shower safer. We install recessed lights, exhaust fans, and timers in Brookside bathrooms. Proper venting to the exterior is required by code, and we make sure the fan moves enough CFM for the size of the room.

Shower Enclosure and Surround Installation

Shower surrounds and enclosures come in acrylic, fiberglass, and tile-ready kits. We install them in Brookside over properly prepped walls, seal the joints, and make sure the enclosure is square. This is a cost-effective way to update a bathroom without a full custom tile job.

Walk-In Shower Repair and Maintenance

We repair walk-in showers in Brookside that have loose tile, failing grout, or slow drains. Maintenance visits include re-caulking, grout sealing, and drain cleaning. Keeping up with small repairs prevents bigger water damage and extends the life of the shower.

Shower Leak Detection and Repair

A shower leak in Brookside can show up as a stain on the ceiling below or a soft spot in the floor. We use moisture meters and visual inspection to find the source, whether it is a failed pan liner, a loose drain, or cracked caulking. We repair the leak and verify it is dry before closing up.

Shower Caulking and Grout Repair

Failed caulking and grout are the first signs of water intrusion. We remove old caulk, clean the joints, and apply new silicone caulk or grout in Brookside showers. This is a maintenance task that should be done every few years, especially in bathrooms with heavy use.

Walk-In Shower Replacement

When a walk-in shower is beyond repair, we replace it. In Brookside, this often means removing a failed pan, updating the valve, and installing a new waterproofed shower with fresh tile or panels. We handle the demo, disposal, and full installation so you are not coordinating multiple contractors.

Emergency Shower Installation

When a pipe bursts or a shower pan fails, you need help fast. We offer 24/7 emergency shower installation in Brookside, including temporary fixes and full replacements. Our truck carries common valves and pans so we can get your shower working again without waiting on a special order.